Outils pour utilisateurs

Outils du site


2 Make certain that the electric motor is always operating at ranked present The primary factor for the overload operation of the electric motor is that the drag load is as well large, the voltage is reduced, or the mechanical jam brought on by the drive is triggered. If the overload time is as well long, the electric motor will take in a huge quantity of active power from the grid, the current will increase swiftly, and the temperature level will climb as necessary, which will quickly melt the motor. For that reason, it is required to guarantee that the electric motor is always run at the ranked existing, and likewise take notice of inspect the operation of the transmission, the concentricity of the coupling as well as the gear transmission.

Third, the old as well as old (eliminated) motors are still being used. These motors utilize Course E insulation, which is bulky, has poor beginning performance as well as reduced efficiency. Although it has gone through an annual change, there are still lots of places being used.

In the job, everybody has to have come across a lot of motor burning, some as a result of mechanical problems, some because of the warmth problem, and also some as a result of the lack of phase and also melted.

Throughout the procedure of the motor, there shall be no dust, water stains and sundries within 3 meters of the air inlet. Otherwise, if it is sucked right into the electric motor, a short-circuit medium will certainly be created, or the cable insulation layer will be damaged, triggering a short circuit between the turns and also burning the motor.

The three-phase A/C electric motor is mostly composed of a stator as well as a blades. When a three-phase rotating existing is put on the stator, a revolving electromagnetic field is generated. If you loved this article and you simply would like to be given more info pertaining to Gear Motor Factory kindly visit the website. The electromagnetic field constantly has two poles (likewise probably in sets), specifically the N pole (north pole) as well as the S pole (north pole), likewise called a counter pole. When the winding mode of the Air Conditioning electric motor stator winding is various, the number of magnetic posts of the produced turning electromagnetic field is different. The number of poles straight influences the speed of the motor. Their connection is: simultaneous rate = 60 × regularity/ level logarithm. If the simultaneous rate of the motor is 1500 rpm, the pole pair number can be computed according to the above formula, which is a 4-pole electric motor. The synchronous rate as well as the number of pole pairs are the standard criteria of the motor as well as can be discovered on the nameplate of the motor. Due to the fact that the post pair can impact the speed of the electric motor, you can change the speed of the motor by transforming the post set of the motor.

What is a carbon brush? Answer: The within the brush motor is put on the surface area of the commutator. When the electric motor rotates, the electrical energy is sent out to the coil with the phase converter. Since its major part is carbon, it is called carbon brush, which is easy to use. The replacement needs to be maintained regularly as well as the carbon deposits should be cleaned up.

Frequency. A lot of follower as well as pump tons are chosen according fully load need, as well as the majority of the time in real application is not at full lots. Since the Air Conditioning motor rate law is very hard, the wind deflector, the return valve or the opening and also closing time are commonly used to readjust the air volume or circulation rate. At the same time, it is tough for the huge electric motor to regularly begin and also quit under the power regularity state, and the power effect is big, which will certainly cause power loss and also Present shock when beginning the shutdown. Direct control of follower as well as pump lots by regularity converter is one of the most clinical control method. When the electric motor is performing at 80% of ranked rate, the power saving effectiveness is close to 40%. At the exact same time, shut loophole constant voltage control can be realized, and energy conserving effectiveness will certainly be even more enhanced. Since the frequency converter can realize the soft quit as well as soft start of the big electric motor, the voltage shock throughout start-up is avoided, the electric motor failing rate is lowered, the service life is extended, and the capability requirement as well as responsive power loss of the power grid are additionally decreased.

The offered frequency size and also the starting current size are not necessarily associated. The size of the starting current depends on the setup of the beginning V/F curve and the length of the velocity time. For liquid tons, the torque called for throughout operation is not continuous. Therefore, the use of several power curves can make the tools run more energy-efficient and also bring financial benefits to individuals.

4 Observe the motor for resonance, noise and unusual odor If the motor vibrates, the component of the load connected to it will certainly become higher, increasing the tons on the motor, as well as overwhelming will certainly shed the motor. Sound as well as smell are forerunners to motor failure as well as should be observed in any way times. Therefore, the electric motor in operation, particularly the high-power maintenance network motor ought to be examined often to see if the motor end cover, support bolts, bearing gland, and so on are loose, and so on, as soon as the issue is found, it should be settled in time.

elect_ic_moto_p_otection_5_successful_st_okes.txt · Dernière modification: 2019/08/20 19:12 par rodolfophillips